Worcestershire Butter Roast Beef. A simple method for perfect juicy roast! (2024)

FAQs

What is the secret to a perfect roast? ›

Buy the best meat you can afford, it really makes all the difference. Let the meat come up to room temperature before roasting (30 minutes). Rub with oil, salt and herbs. Ideally brown the meat in a pan first or roast on a high heat for the first 20 minutes.

While the beef is cooking, lift it out of the oven from time to time, tilt the tin and baste the meat really well with its own juices – this ensures that the flavour that is concentrated in the fat keeps permeating the meat, and at the same time the fat keeps everything moist and succulent.

Reheat with a liquid: One way to add moisture back into the beef is to reheat it in a liquid such as broth or gravy. You can do this by placing the beef in a pot or slow cooker with the liquid and heating it until it's heated through and tender.

The Chateaubriand beef tenderloin roast is considered to be the most tender cut of beef for a roast. This cut of beef comes from the loin area of the cow, which is right below the backbone, behind the rib section and in front of the sirloin section.

A surefire way to make a tender, juicy pot roast is through braising; that is, cooking the meat in a small amount of liquid in a tightly covered pot at low temperature.

With a few extra steps, you can take a day-old, dry roast and make it moist and juicy again. One of the easiest ways, says Sidoti, is to use a slow cooker or pot with a lid. Place meat in the slow cooker or pot. Add 2 to 3 cups of liquid (your choice) with enough to cover about halfway but not fully.

When roasting meat and poultry, set the oven temperature to 325°F (163°C) or higher. Explore the charts below to learn how to get great results every time you cook.

When cooking a roast in the oven, keep it uncovered until roasted to the desired doneness. After removing from the oven, tent with foil and let stand 15 minutes before carving. This allows the juices to redistribute, preventing them from draining out during carving—and preventing dry, disappointing meat.

Brining makes meat juicier. Unbrined meat loses 30 percent of its moisture, while brined meat loses only 15 percent. Make a brine by combining 1 cup of salt to 1gallon of water. Brine the meat about four hours and rinse thoroughly.

Cook at a low temperature: Cook at 300 degrees F so the connective tissues can gradually break down, instead of seizes up at a higher temperature. Use a moist cooking environment: Add broth to the pot roast to create and cover with a lid or foil to trap in steam and moisture to prevent the meat from drying out.

Why is my roast still tough after 6 hours? ›

There are several reasons why this could have happened even after so much cooking. First, your choice of a rump roast could be a factor since cuts from the hind quarter are very muscular and, since muscles are the most resistant to breaking, this cut is quite stubborn when it comes to becoming tender.

Remove the roast from the oven when it reaches its finished temperature – 145ºF (63ºC) for medium-rare, 160ºF (71ºC) for medium or 170ºF (77ºC) for well done. Bone-in prime rib will take an extra 30 to 45 minutes; tenderloin will take 30 to 60 minutes less. (See our chart below for cooking times.)

We recommend a temperature of 195-200 °F / 90-93 °C for a tender and juicy roast. Serve: Remove the bay leaves and rosemary sprigs. Blend some of the celery, carrots and onion with some of the juices until you have a smooth puree. Spoon some of the puree sauce on each serving plate and top with the roast.

To cook it until it's so tender it falls apart, you'll need to choose a joint like chuck and blade or beef brisket and either braise, slow roast or slow cook it for at least a couple of hours.

I opt for basil, thyme, paprika, dried bay leaves, and black pepper. These add a lovely, almost Italian-inspired flavor to this pot roast recipe. Veggies. Including onions, garlic, carrots, and potatoes (all of which are also in my beef stew!).

When cooking a roast in the oven, keep it uncovered until roasted to the desired doneness. After removing from the oven, tent with foil and let stand 15 minutes before carving. This allows the juices to redistribute, preventing them from draining out during carving—and preventing dry, disappointing meat.

There are several reasons why this could have happened even after so much cooking. First, your choice of a rump roast could be a factor since cuts from the hind quarter are very muscular and, since muscles are the most resistant to breaking, this cut is quite stubborn when it comes to becoming tender.